EMT Practice Test

1. Question Content...

---

Question1: Click the Exhibit button.

What is accomplished by the default-gateway parameter in the configuration shown in the exhibit?

Question2: Click the Exhibit button.

Referring to the exhibit, you want to ensure that routers in Area 20 can connect to routers in Area 0.
Which two steps must be done to allow this behavior? (Choose two.)

Question3: To reduce the size of OSPF Area 100, you configure the area with the no-summariesparameter. After committing this configuration change, you notice that an OSPF router in a remote area is no longer receiving Type 5 LSAs from an ASBR in Area 100.
Which statement is true in this scenario?

Question4: Click the Exhibit button.

The route shown in the exhibit is being advertised to the EBGP peer and displays a next hop of itself.
However, you do not have a next-hop self policy configured. What would cause this behavior?

Question5: Click the exhibit button.

What would be the expected outcome from the configuration shown in the exhibit?

Question6: Click the Exhibit button.

After an acquisition, a customer experiences OSPF flooding during network consolidation and the router is experiencing performance problems. Referring to the exhibit, which OSPF feature set should you add or modify to increase capacity?

Question7: You are configuring a BGP-signaled Layer 2 VPN service.
Which two statements are true in this scenario? (Choose two.)

Question8: Which two statements are correct regarding site IDs and circuit IDs in a VPLS routing instance? (Choose two.)

Question9: Click the Exhibit button.

You have configured the OSPF network as shown in the exhibit. However, R4 and R5 do not have connectivity to prefixes outside of Area 10. In this scenario, what will solve this problem?

Question10: Click the Exhibit button.

Referring to the exhibit, in which order will ICMP traffic be processed by the configured filters and policers for interface ge-1/0/0?

Question11: Click the Exhibit button.

Referring to the exhibit, the Layer 2 VPN between PE-1 and PE-2 is not functioning properly.
What must you do to solve the problem?

Question12: Click the Exhibit button.

BGP routes received on R5 are redistributed into the IS-IS network. You want the redistributed routes to be present in Area 49.0001.
Referring to the exhibit, how would this task be accomplished?

Question13: You want to reject routes from any BGP peers that have prepended their AS path.
What is the correct as-pathregex that would allow you to accomplish this task?

Question14: Click the Exhibit button.

The exhibit shows a BGP peering session for two PE routers. The BGP session is up, but IPv4 hosts in the Layer 3 VPN that use the BGP session are unable to communicate.
What is the problem?

Question15: Which message type initiates the BGP session?

Question16: Which neighbor state indicates that two BGP neighbors have full connectivity?

Question17: Click the Exhibit button.

The customer's hosts cannot communicate across their Layer 3 VPN. The exhibit shows the configuration for the two PE devices in the Layer 3 VPN.
What should you do to solve the problem?

Question18: Click the Exhibit button.

Referring to the exhibit, RR1-RR4 are route reflectors.
Which three routers would RR1 need to peer with if the no-client-reflect parameter has been configured?
(Choose three.)

Question19: Which two types of LSAs have a domain scope? (Choose two.)

Question20: How does Juniper Networks use selective BGP route damping to help stabilize the network?

Question21: Click the Exhibit button.

You have configured a BGP-signaled Layer 2 VPN with the configuration shown in the exhibit.
Which two statements are true in this situation? (Choose two.)

Question22: Click the Exhibit button.

You have deployed route reflectors in your network. You are receiving the route 200.0.0.0/24 from AS10 and AS6 and are seeing the oscillation happening as shown in the exhibit.
What are two ways to solve this issue? (Choose two.)

Question23: Click the Exhibit button.

You have configured Layer 2 VPN stitching between two Layer 2 circuits on PE2, but traffic is not passing through the VPN.
Referring to the exhibit, what is the problem?

Question24: Click the Exhibit button.

Referring to the exhibit, what must be added to the existing configuration to ensure that per-prefix load balancing occurs?

Question25: Click the Exhibit button.

Which two statements are true regarding the output shown in the exhibit? (Choose two.)